Selection of Jinan color steel plate: good bearing capacity; Beautiful appearance; Large plate utilization coefficient, convenient connection mode, and the wave distance and waveform in line with the domestic mode are preferred. With factory certificate and product quality certificate, and indicate the product standard number, steel plate number, galvanized quantity, surface structure, surface quality, specification and dimension, shape accuracy, etc.

豎向布置墻板。Wall panels shall be arranged vertically.

豎向布置墻板時，宜采用帶形窗，這樣的隔斷可以減少洞口結構，有利于防雨。使用單面窗戶時，窗戶兩側結構復雜，施工不容易出現漏雨現象，板材排布時選用排版起始線，板材排列與開口尺寸協調，橫向布置墻板時，主要解決窗面兩側結構復雜，施工不容易出現漏雨現象，板材排版時選用開式起線。

When the wallboard is vertically arranged, the strip-shaped window should be adopted. Such partition can reduce the portal structure and is conducive to rainproof. When the window is constructed, the size of the opening plate is not coordinated with that of the opening plate. When the opening plate is used for construction, it is easy to be leaked. When the opening plate is used for drainage, it is easy to be arranged on both sides. When the opening plate is used for construction, it is easy to be leaked. When the opening plate is used for drainage, the size of the opening plate is not coordinated with that of the window.

彩板墻的長度包括：從檐口的封閉標高到墻底的起始高度；從檐口的封閉高程到洞口上方表面的高度；從洞口下面到洞口的上表面的高度，從洞口下表面到墻底的起始高度等三種，因此在確定板長之前，建議確定檐口、窗、門洞和其他洞口的高程和結構做法，并以此來布置墻面檁條的位置，從而計算墻面板的長度，一般情況下，由于對其美觀要求的要求，彩板墻面在垂直布置時不宜采用這種方法。如墻高較大，才考慮采用搭接法，此時墻面的長度應加上搭接長度。山墻檐口為斜截面時，每一板的坡度計算其大值。

The length of the color board wall includes: from the closed elevation of the cornice to the starting height of the wall bottom; The height from the enclosed elevation of the cornice to the surface above the opening; The height from the lower part of the opening to the upper surface of the opening and the starting height from the lower surface of the opening to the bottom of the wall. Therefore, before determining the plate length, the elevation and structural method of cornice, window, door opening and other openings must be determined, so as to arrange the position of wall purlin, so as to calculate the length of wall panel. Generally, due to the requirements of its aesthetic requirements, This method should not be used when the color plate wall is vertically arranged. If the wall height is large, the overlapping method shall be considered. At this time, the length of the wall shall be added with the overlapping length. When the gable cornice is of oblique section, the maximum value shall be calculated according to the slope of each board.

橫向設置壁板。Set wall panels horizontally.

側向布置墻板主要用于夾芯板，有時也用于單層壓型板。這種方法以板寬為模組垂直布置。當設計時，大于板寬的孔時，盡量將孔的上、下邊緣與板的橫向接縫組合在一起，以免造成結構復雜，橫向布置墻板多與柱的中軸線分開，首、末柱之間的板長為柱距尺寸，再加上首末柱的軸線長度為柱距尺寸，中間墻板的長度為柱距尺寸，以及柱軸線的長度為柱距尺寸等。根據坡度不同，斜坡出的板長。

The side wall panels are mainly used for sandwich panels and sometimes single-layer profiled panels. This method takes the board width as the vertical layout of the module. In the design, when the hole is larger than the plate width, try to combine the upper and lower edges of the hole with the transverse joint of the plate, so as not to cause complex structure. The transverse wall plate is mostly separated from the central axis of the column. The plate length between the head and end columns is the column spacing dimension, plus the axis length of the head and end columns is the column spacing dimension, and the length of the middle wall plate is the column spacing dimension, And the length of the column axis is the column spacing size, etc. According to the slope, the length of the slab from the slope is different.

無絕緣板連接。No insulation board connection.

非絕熱板連接有兩種：顯露連接和隱式連接。當接合時，將接合的緊固件連接到接縫處，接合處與墻梁連接。這樣的聯接，使扣件頭部在墻面凹陷處更美觀。當某些波距較大時，連接緊固件也可設置在峰頂。隱接板覆蓋面較窄，將塊板與墻面連接后，將第二塊板插入塊板的板邊槽，起到抗負風壓的作用。

There are two types of non adiabatic plate connection: exposed connection and implicit connection. When joining, connect the joined fasteners to the joint, and the joint is connected with the wall beam. Such connection makes the fastener head more beautiful in the concave part of the wall. When some wave distances are large, the connecting fasteners can also be set at the peak. The coverage of the concealed board is narrow. After connecting the first board with the wall, insert the second board into the side groove of the first board to resist negative wind pressure.

夾板聯接。Splint connection.

夾芯板墻板的連接方式有工字鋁連接、插座連接和暗扣連接。

The connection modes of sandwich panel wall panel include I-shaped aluminum connection, socket connection and concealed buckle connection.彩鋼墻體基礎結構。

Color steel wall foundation structure.

墻體基礎結構主要解決防止雨水滲入室內的問題。為防止墻面留下的雨水滲入室內，連接處的地板和矮墻頂部混凝土澆筑成高達60毫米的彩色鋼板混凝土框架。

The wall foundation structure mainly solves the problem of preventing rainwater from penetrating into the room. In order to prevent the rainwater left by the wall from penetrating into the room, the floor at the connection and the top of the low wall are concreted into a colored steel plate concrete frame up to 60mm.